10530SBEBOwner's Manual
10TO USE CHOKE CON TROL (See Fig. 12)The choke con trol is located on the en gine. Use the choke control when ever you are starting a cold en gine. Do
11TO MOVE FORWARD AND BACKWARD (See Fig. 16)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con
12TO ADJUST SKID PLATES (See Fig. 18)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each
13COLD START - ELECTRIC STARTER1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the k
14MAINTENANCELUBRICATION CHARTGENERAL REC OMMENDA TIONSThe warranty on this snow thrower does not cover items that have been sub jected to operator ab
15MAINTENANCEV-BELTSCheck V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad justable
16WARNING: To avoid serious injury, before per-forming any service or ad justments:1. Be sure throttle is in STOP position.2. Remove safety ignition k
17SERVICE AND ADJUSTMENTSTO REPLACE BELTS (See Fig. 22)The auger and traction drive belts are not adjustable. If the belts are damaged or begin to sli
18STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never
19TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93
21KEY PART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley, Impeller 5 532 18 89-09 Bearing Assembly, Flange 6 532 15 53-
22REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTESNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961
23KEY PART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 19 84-75 Control Assembl
24REPAIR PARTS HANDLESSNOW THROWER - MODEL NO. 10530SBEB (961
25KEY PART NO. NO. DESCRIPTION 1 532 18 41-10 Lever, Auger Control, RH 2 532 18 41-09 Lever, Traction Drive Control, LH 3 532
26REPAIR PARTS DRIVESNOW THROWER - MODEL NO. 10530SBEB
27KEY PART NO. NO. DESCRIPTION 1 532 14 63-15 Screw, Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15
28REPAIR PARTS CHASSIS / ENGINE / PULLEYSSNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODU
29KEY PART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, Traction Idler 2 532 18 05-22 Pulley, Idler (2-1/4) 3 - - -
3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man ufactured to give best possible dependability and p
30REPAIR PARTS WHEELS / DECALSSNOW THROWER - MODEL NO. 10530SBEB (96193001300
31KEY PART NO. NO. DESCRIPTION 1 532 19 95-01 Wheel Assembly, 12", Power Steering, LH 2 532 15 54-43 Pin, Klik 1/4 3 53
532 40 37-62 Rev. 3 06.06.06 BY Printed in U.S.A.SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Hus
4PARTS PACKED SEPARATELY IN CARTON
5ASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Rea
6ASSEMBLY / PRE-OPERATIONINSTALL AUGER CONTROL ROD (See Figs. 5 and 6)The auger control rod has the short loop on the end of the spring as shown.1.
7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinfl ated at the fac-tory for shipping purposes. Correct and equal
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9OPERATIONChoke control - used for starting a cold engine.Traction drive control lever - used to engage power-pro-pelled for ward or reverse motion of
Kommentare zu diesen Handbüchern