EEEEnnnngggglllliiiisssshhhh 338XPT Calif ornia Oper ator’s manual (EPA III, CARB III) Please r ead the operator’s manual carefully and make sure yo
10 – EnglishGENERAL SAFETY PRECAUTIONSMufflerThe muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.In
English – 11GENERAL SAFETY PRECAUTIONSBar• Length (inches/cm)• Number of teeth on bar tip sprocket (T). • Chain pitch (inches). The spacing between th
12 – EnglishGENERAL SAFETY PRECAUTIONSSharpening cutting teethTo sharpen cutting teeth you will need a round file and a file gauge. See instructions und
English – 13GENERAL SAFETY PRECAUTIONS• Loosen the bar nut that holds the clutch cover and chain brake. Use the combination spanner.• Raise the tip of
14 – EnglishGENERAL SAFETY PRECAUTIONS• Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked.
English – 15ASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han
16 – EnglishFUEL HANDLINGFuelNote! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke
English – 17FUEL HANDLINGFuelingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at l
18 – EnglishSTARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake should be activated when starting the chain saw. Activate t
English – 19STARTING AND STOPPING• The chain brake should be activated when starting. Se instructions under the heading Start and stop. Do not drop st
2 – English KEY T O SYMBOLS Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fat
20 – EnglishWORKING TECHNIQUESBefore use:1 Check that the chain brake works correctly and is not damaged.2 Check that the throttle lock works correctl
English – 21WORKING TECHNIQUES7 Take great care when cutting a tree that is under tension. A tree that is under tension may spring back to its normal
22 – EnglishWORKING TECHNIQUES8 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is
English – 23WORKING TECHNIQUESCut all the way through the log from above. Avoid letting the chain touch the ground as you finish the cut. Maintain full
24 – EnglishWORKING TECHNIQUES• Weight of snowYou may find you are forced to let the tree fall in its natural direction because it is impossible or dan
English – 25WORKING TECHNIQUESWhen the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felli
26 – EnglishWORKING TECHNIQUESHow to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the chain sa
English – 27MAINTENANCEGeneralThe user must only carry out the maintenance and service work described in this manual.Carburetor adjustmentDue to exist
28 – EnglishMAINTENANCEHigh speed jet HAt the factory the engine is adjusted at sea level. When working at a high altitude or in different weather con
English – 29MAINTENANCEThrottle lock• Make sure the throttle control is locked at the idle setting when the throttle lock is released.• Press the thro
English – 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s ma
30 – EnglishMAINTENANCEMufflerNever use a machine that has a faulty muffler.Regularly check that the muffler is securely attached to the machine.Some muf
English – 31MAINTENANCETensioning the recoil spring• Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockw
32 – EnglishMAINTENANCEthat the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier i
English – 33MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des
34 – EnglishTECHNICAL DATATechnical data338XPT CaliforniaEngineCylinder displacement, cu.in/cm32,7/45Cylinder bore, inch/mm 1,7/43Stroke, inch/mm 1,22
English – 35TECHNICAL DATARecommended original and replacement bar and chain combinationsFollowing is a list of recommended cutting equipment for the
36 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (U.S. Environmental Protection Agency), CARB (Calif
English – 37AMERICAN STANDARD SAFETY PRECAUTIONSSafety precautions for chain saw users(ANSI B 175.1-2000 Annex C)Kickback safety precautionsWith a bas
4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates b
´®z+SK•¶5C¨2009-01-20´®z+SK•¶5C¨1151439-95
English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Filter cover2 Adjuster screws carburetor3 Starter4 Fuel tank5 Chain oil tank6 Chain
6 – English GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor
English – 7 GENERAL SAFETY PRECA UTIONS chain sa w usage if possible. Your dealer, forestry school or your library can provide information about wh
8 – English GENERAL SAFETY PRECA UTIONS • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine driv
English – 9GENERAL SAFETY PRECAUTIONSWill my inetria activated chain brake always activate during kickback in the event of a kickback?No. First your b
Kommentare zu diesen Handbüchern