Husqvarna M7 Bedienungsanleitung

ManualRead the safety instructions.

Assembly: frameThe right and left leg units of theframe are assembled in thesame way. The bolts listedbelow are for one leg unit.(1) Fit the horizonta

11(6) Fit the strut to the inside (D)of the guide rail flanges with theoval hole up. (4 x M6x20 collarbolts, 4 x M6 collar nuts)(5) Place the guide r

Assembly: log bed(8) Place the plastic slide rail onthe log bed. Fit the longer (A)scale against the plastic rail onthe right log bed and the shorter(

(15) The ends of the ratchetcam axle are different. Insertthe one that has the recessnearest the tip through the lowerhole in the long leg.(16) Threa

18A17AAssembly: edge support(18) Slide the edge support ontothe log bed.(A) Attach crank handle to thecrank rod. Insert an allenwrench into the end of

(19) Insert bolts through theholes along the sides of both thechain-saw bed (pylon) and thespool holder plate. Turn thesquare nuts a few times. (8xM6x

24(22) Fit the chain guard on thesupport and bolt. (2 x M6x40collar bolts, 2 x M6 locking nuts)2322Remove the two bolts holdingthe guide bar and remov

(25) Fit the Logosol extendernuts through the chain-sawplate using the front hole. (Forsome chain-saw models therear hole has to be used toensure that

(28) Screw the handle with awasher on the threaded rod forthe log grip carriage. (1 x M6washer)(29) Insert the bolts and screwon square nuts in the sa

M7When setting up the M7directly on the ground:The surface must firm andlevel enough that driving anormal car on it would not be aproblem.Fit a board

(A) Check that when the log bedis cranked down, it moveseasily through the saddle platedriven by its own weight. If thisis not the case:- Stop the log

The guide bar should beparallel to the log bed. If thisis not so, the guide bar isprobably not straight. Removethe chain from the guide barwithout rem

Step-by-step sawing instructions221.1 Roll the log onto the logbed.1.2 Fasten the log in placeusing the edge support. Placethe edge support armsbackwa

In the beginning it might serveyou well to make a drawing onthe top end of how you want topiece the log. Use a thickmarker so that the linecorresponds

24Generally, once the wood issawn it must be dried.It is possible to use undriedwood in some construction, butonly keeping in mind a 7%shrinkage in wi

25Reasons for wrongmeasurements on anM7 sawmill.A. Incorrect adjustmentor set-up.B. Cutting equipmentmisfunction.C. Tensions in thewood.A. Checking th

26Tensions in the wood cansometimes result in similarsymptoms as faults in thecutting equipment.C. Tensions in thewoodThe M7 sawmill can only sawstrai

27must learn to file before thechain gets dull.File comfortablyBoth hand and electrical chainfiling can give good results. Theelectrical is faster and

28Logosol offers a great range of extensions, special tools and other accessories for the M7 WoodWorkers Mill. Simple extensions can be bought in 0.5

292Article listNo. Article number # Description1. 4507-001-1000 2 Guide rail, 2.75 m (9 ft)2. 4507-001-1015 2 Guide railstrut3. 4517-001-1009 1 Cross

World serviceThose who haven’tordered directlyfrom Logosol.Everyone who bought directlyfrom Logosol in Madison isalready fully registered here.Those o

EU DeclarationProduct: Logosol M7 portable sawmillManufacturer: Logosol KB, Industrigatan 13SE-871 53 HärnösandTel. +46 (0)611 18285The company hereby

0 1020304050607080M6 M8 M10M6x30 Bolt Sawmill Bolt SizesCollar nut Collar bolt Allen head bolt30 mmMetric scale in mmBAG 71 BAG 72-73 BAG 74 BAG 75 BA

Design and construction of theM7 WoodWorkers Milll, plusmanual text and pictures:Mattias Byström.As LOGOSOL is constantlydeveloping and improving allm

other than the operator is 8 m(26 feet) from all sides exceptwhere the logs are rolled in.The safety distance from thisside is 15 m (50 feet), due to

ALWAYSREMEMBER that shouldany type of problem occur,stop sawing and turn off thechain-saw. Most accidentswith dangerous machineshappen when somethingg

- Because of the high qualityand precision construction,none of the angles need setting.The only parts to adjust are theguide rail and the height of l

What follows is a brief description of the M7components to assist in identifying them duringassembly. A more complete listing is found at the endof th