Operator’s manual (EPA II)Please read these instructions carefully and makesure you understand them before using the machine.English323E 325EX-series
10 – EnglishSAFETY INSTRUCTIONSGeneral working instructionsIMPORTANT INFORMATION• This section takes up the basic safety precautions for working with
English – 11SAFETY INSTRUCTIONSSafety instructions after completing work• Ensure the blade has stopped before cleaning, car-rying out repairs or an in
12 – EnglishWHAT IS WHAT?What is what on the edger?1. Blade2. Grease fi ller cap3. Angle gear4. Blade guard5. Shaft6. Loop handlebar7. Throttle8. Stop
English – 13Assembling the bladeFit the blade as follows:1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fi ts in the ho
14 – EnglishNOTE! The edger is fi tted with two-stroke engines and must always be run on a mixture of gasoline and two-stroke oil. To ensure the correc
English – 15Control before startingWARNING!When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (bla
16 – EnglishBasic setting• The carburetor is set to its basic setting when test run at the factory. The basic setting should be kept during the machin
English – 17Correctly adjusted carburetorA correctly adjusted carburetor means that the machine ac-celerates without hesitation and the machine 4-cycl
18 – EnglishA muffl er fi tted with a catalytic converter reduces the extent of the following substances in the exhaust fumes:• Hydrocarbons (HC). Some
English – 19Lubricating the fl exible drive axleAdjusting the edgerʻs cutting depthMAINTENANCEInside the edgerʻs drive shaft is a fl exible drive axle.
2 – EnglishEXPLANATION OF SYMBOLSSymbolsWARNING! The edger can be dangerous!Careless or incorrect use can result in serious or fatal injury to the ope
20 – EnglishNOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operat
English – 21TECHNICAL DATATechnical dataEngineDisplacement, cu. in/cm3 Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpmIdling
22 – EnglishEMISSION CONTROL WARRANTY STATEMENT If you have any questions regarding your warranty rights and responsibilities, you should contact you
English – 23NOTES
2004W47114 03 40-95´®z+HB)¶58¨´®z+HB)¶58¨
English – 3List of contentsSYMBOL EXPLANATIONSymbols ...2CONTENTSList of
4 – EnglishSAFETY INSTRUCTIONSPersonal protective equipmentIMPORTANT INFORMATION• An edger used incorrectly or carelessly can become a dangerous tool,
English – 55. Muffl erThe muffl er is designed to give the lowest possible noise level and to direct the engineʼs exhaust fumes away from the operator.
6 – EnglishSAFETY INSTRUCTIONSIMPORTANT INFORMATION• All service and repairs to the machine require special training.• This applies especially to the
English – 76. Cutting equipmentSAFETY INSTRUCTIONSThe two basic rules:1. Only use the cutting equip-ment we recommend! See chapter “Technical data”
8 – EnglishGeneral safety instructionsSAFETY INSTRUCTIONSIMPORTANT INFORMATION• The machine is only designed for cutting the edges of lawns.• The only
English – 9SAFETY INSTRUCTIONSTransport and storage• Store and transport the machine and fuel so that any leakage or fumes do not risk coming into con
Kommentare zu diesen Handbüchern